Desinformado
 

Hackint0sh: Guide to Turbosim

iphone unlocking tools Hackint0sh: Guide to Turbosim

If you recently bought an iPhone with the Bootloader 4.6 (like Me) you may now know that the only real solution to unlock this little boy (except AT&T) is using a Turbosim, here is a guide posted at hackint0sh that illustrate you on how to perform a TurboSim unlocking, have an iPhone, 2 tons of patience and this guide… of course good luck.

You can waste a lot of money if you get this wrong.

1. Get an iPhone. Try an applestore, or even ebay.
2. Once you get it, make sure you read the manual.
3. At the top of the phone is the SIM card tray, in there is your AT&T sim. Go on, have a look. Now put it back.
4. Use one of the many, many well documented methods to activate your phone. Any of them will be fine, and if you can get to this part then you can probably continue.
5. Order a TurboSIM (Blank version) from www.bladox.com
6. Wait.
7. Wait.
8. If you ordered via an express shipping method you can skip to step 11
9. wait
10. wait a bit more

11. You could have done this step while you were waiting, but install SSH. Use these instructions http://cre.ations.net/blog/post/howt…on-your-iphone (in the comments there is a mac version of the SSH installer)

While you are at it install the iPhone binary kit, too: http://iphone.natetrue.com/iphone-binkit-0.06.tar.gz

12. Once you have done that and are able to ssh into your phone over wireless (if you dont know how already then I suggest you give up now. cancel your order with bladox.)

Hint 1: Find your iPhone IP address under: Settings ->WiFi -> -> blue arrowy thing

Hint 2: Either using Putty (for windows) or ssh (for mac from the terminal) use that IP address to connect to the iPhone. E.g: ssh -l root 123.123.123.123

The root password is dottie. I suggest you change it unless you want someone like me to totally take the shine off your afternoon.

13. download the iPhone port of the bladox utilities: http://www.gofilego.com/?fileid=71ae…3da7541ee37ae8

Extract these files and in there somewhere you will see a little file called “turbo-app” copy this to your iPhone using scp for instance:

scp turbo-app root@123.123.123.123:/

Download this: http://www.bladox.com/pub/applesaft-0.92.tar.gz

in the “bin” directory copy applesaft.trb to the iphone:

scp applesaft.trb root@123.123.123.123:/

14. copy the follwing file from the iPhone /System/Library/LaunchDaemons/com.apple.CommCenter.plist

and add the following line:

Disabled

after these lines, already present in the file

OnDemand

Now copy the file back. Yes, to the same location you got it from.

14. now you will have to reboot your iPhone. (Told you to read the manual) You can do this by pressing the power button for a few seconds until it asks you if you want to switch it off, or you can just take out the battery….

15. Now, get your AT&T sim and carefully cut it as indicated in the packet that the TurboSIM came in.

16. Do the same for the SIM you want to be using eventually in the iPhone.

17. CAREFULLY, VERY CAREFULLY. place the AT&T sim along with the TurboSIM into the sim tray and pop it into the iPhone.

It should slide in without too much effort, DO NOT FORCE IT IN. BE CAREFUL.

18. Now ssh into your phone and do the following (yes include the slashes):

chmod 755 /turbo-app
/turbo-app /applesaft.trb

This will take several seconds to run just be patient.

19. Go to Settings -> Phone -> SIM Applications -> Apple Saft and then click SET.

20. Eject the sim tray CAREFULLY.

21. CAREFULLY, REALLLY EFFING CAREFULLY, put the TurboSIM and your target SIM into the iPhone.

22. Remember that file I told you to edit? Right edit it again and take out that line I told you to put in, then copy it back to the iPhone.

23. Do 14. Again.

24. Fingers crossed it should be working now.

25. Go to Settings -> General -> Network -> EDGE and change your details according to your operators instructions.

26. Thank everyone who has put time and effort into this, including Ozbimmer, ZF, the bladox developers. Yadda yadda.

OK? Any questions? I can answer all of them:

a) read the instructions again
b) google for it.
c) search the forums for it.


-
Desinformado.con en Español

Share and Enjoy:
  • printfriendly Hackint0sh: Guide to Turbosim
  • digg Hackint0sh: Guide to Turbosim
  • stumbleupon Hackint0sh: Guide to Turbosim
  • delicious Hackint0sh: Guide to Turbosim
  • facebook Hackint0sh: Guide to Turbosim
  • yahoobuzz Hackint0sh: Guide to Turbosim
  • twitter Hackint0sh: Guide to Turbosim
  • googlebookmark Hackint0sh: Guide to Turbosim


   



One Comment, Comment or Ping

  1. boneshaker

    Hi guys,I tried the steps above, but I get stuck at the point where you have to disable the commcenter.When I do,my iphone does not stay on for more than a minute to complete the loading.what can I do prevent the iphone from restarting so early.

Reply to “Hackint0sh: Guide to Turbosim”

Desinformado Search Engine







Subscribe to Our RSS Feed and Receive the Latest Information about Gadgets, Products, Reviews in your Mailbox, Spam Free:

Delivered by FeedBurner



Blog WebMastered by All in One Webmaster.
WordPress SEO fine-tune by Meta SEO Pack from Poradnik Webmastera